K2 DynoReplay ControllerInstallation ManualSoftware Version 1.6071-8744-01April 2010
Overview diagramThe following diagram illustrates a typical K2 Dyno Replay System. If your installationrequires a different system configuration, apply
Installation instructionsDescriptionK2 systemGrass Valley preinstallssoftware, licenses, and teststhe units together before youreceive the Dyno-Pack.R
CommentTaskstandard. On K2 Summit ProductionClient, the license must be installed, ifnot already present. Refer to release notesfor compatibility info
Procure software and/or hardwareDepending on your desired system, procure the following items so that they areavailable for the installation process.
Chapter 2Cabling systemsThis section contains the following topics:• Cable K2 Summit Production Client• Cable K2 Solo Media Server• Cable ChannelFlex
Cable K2 Summit Production Client1. If desired, mount the K2 Summit Client in an equipment rack. Refer to the K2System Guide for rack mount procedures
C1 C2USB/1394100-240 V-4-2A,60-50Hz100BT/1000BTGPIVGAREF. LOOP THROUGHSDI IN1 SDI OUT1 SDI OUT2LTC I/OAESAUDIO RS422SDI OUT1 SDI OUT2AESAUDIO RS422LTC
Cable K2 Dyno ControllerMake K2 Dyno Controller cable connections as illustrated.100-240 V~4A 50-60H zRS-232PowercordKeyboardand mouseVGAmonitorEthern
If you require a connection for media (FTP/Streaming), connect as illustratedand configure as instructed later in this manual.13 April 2010 K2 Dyno Co
Affiliate with the N.V. KEMA in The Netherlands CERTIFICATECertificate Number: 510040.001 The Quality System of: Thomson Inc, and its worLdwide Grass
Chapter 3Configuring networksThis section contains the following topics:• About K2 Dyno Replay Controller modes• Configure network on K2 Dyno Controlle
About K2 Dyno Replay Controller modesThe K2 Dyno Reply Controller operates in the following modes:• Dyno mode – The Dyno application is open for norma
7. Continue with standard Windows procedures to configure the TCP/IP protocolproperties. You can set up the network using DHCP, DNS, WINS, or other sta
• Password: adminK2(The password is case sensitive)At first startup, End User License Agreements appear on the screen. Accept theagreements to continue
NOTE: On small networks or networks with certain security policies a DHCPserver or domain name server (DNS) might not be available. In this case youc
Chapter 4Installing and configuring softwareThis section contains the following topics:• About K2 Dyno software• Install K2 Dyno Server software• Enab
About K2 Dyno softwareThere are two software components in the K2 Dyno Replay system, as follows:• K2 Dyno Server software – This software runs on the
4. Under Protected Volumes, set C: to Protected.Do not modify other settings.5. Click OK.6. When prompted, restart the K2 Summit Production Client or
K2 DynoReplay ControllerInstallation ManualSoftware Version 1.6071-8744-01April 2010
4. Select a new session and Next.5. For a typical system, do the following:a) Set C1 and C2 to Recorder.b) Set C3 and C4 to Player.c) Touch Next.6. Fo
4 K2 Dyno Installation Manual 13 April 2010Copyright Copyright © Grass Valley, Inc. All rights reserved. Printed in the United States of America.Porti
ContentsGrass Valley Product Support...7Chapter 1: Over
6 K2 Dyno Controller Installation Manual 13 April 2010Contents
Grass Valley Product SupportTo get technical assistance, check on the status of a question, or to report a new issues,contact Grass Valley Product Sup
TelephoneCountyRegion+91 22 676 10300India1 300 721 495AustraliaPacific0800 846 676New Zealand+61 3 8540 3650For callers outside Australiaor New Zealan
Chapter 1Overview of systemsThis section contains the following topics:• Overview diagram• Connections to K2 systems• K2 Summit/Solo with Dyno install
Comments to this Manuals