Grass-valley Kaleido-IP v.6.02 User Manual

Kaleido-IP Quick Start GuidePart Number: M926-9905-101 7 July 2011

6Setting Up the Kaleido-IP Multi-ViewerSetting up the Kaleido-IP Hardware2Step 1: Physical SetupSetting up the Kaleido-IP HardwareTo set up the Kaleid

Kaleido-IPQuick Start Guide7Cabling DiagramCabling diagram for a Kaleido-IP with two network adapters.The Kaleido-IP-4 model has two additional DATA p

8Setting Up the Kaleido-IP Multi-ViewerNetworking Setup2To change the Kaleido-IP’s management and data IP addresses:1. Configure your client PC or lap

Kaleido-IPQuick Start Guide94. Click the XAdmin button.The XAdmin Status and Options page appears.5. Click System configuration, in the navigation are

10Setting Up the Kaleido-IP Multi-ViewerNetworking Setup26. Under General, type a different name for your system if you wish.7. Under Ethernet, type t

Kaleido-IPQuick Start Guide118. Click Save.The new settings are saved locally.9. Click OK.10. The Apply settings button becomes available.11. Click Ap

12Setting Up the Kaleido-IP Multi-ViewerFinding the Management IP Address and Application Version2Finding the Management IP Address and Application Ve

Kaleido-IPQuick Start Guide134. On the General tab, click Use the following IP address.5. Type an IP address in the same range as the default manageme

14Setting Up the Kaleido-IP Multi-ViewerXEdit Installation2The Local Area Connection Properties window opens.3. On the Networking tab, under This conn

Kaleido-IPQuick Start Guide152. Click the XEdit button.The system will automatically detect the J2SE version on your computer, and, if necessary, will

ii0Copyright © 2011 Miranda Technologies Inc.All rights reserved. ATTENTION: please read the following terms and conditions carefully. By using Kaleid

16Setting Up the Kaleido-IP Multi-ViewerXEdit Installation24. You may see a warning about XEdit’s digital signature. In such a case you may want to se

Kaleido-IPQuick Start Guide175. Depending on your Java settings, the Java Web Start installer may prompt you to confirm whether you wish to have XEdit

18Setting Up the Kaleido-IP Multi-ViewerXEdit Installation27. Once the installation process has completed, XEdit’s main application window appears:Not

Kaleido-IPQuick Start Guide19Installing the Java Runtime EnvironmentXEdit is a Java Web Start application, and thus requires the Java Runtime Environm

20Setting Up the Kaleido-IP Multi-ViewerInstalling the Java Runtime Environment2Another security warning may appear:3. Click Run, to open the installe

Kaleido-IPQuick Start Guide21Java Setup will update your PC or laptop.5. Click Close once the installation has completed.Step 4: System SetupBefore yo

22Setting Up the Kaleido-IP Multi-ViewerConfiguring Transport Streams24. On the Configure menu, click Connect.5. In Connect to Multi-viewer, enter the

Kaleido-IPQuick Start Guide23The settings for the selected multicast stream source appear in the Properties pane.3. Replace the default source name if

24Setting Up the Kaleido-IP Multi-ViewerAdding Stream Sources24. Repeat this until you have completed the required configuration changes to match the

Kaleido-IPQuick Start Guide25The Multicast Stream Configuration window appears.3. In Multicast Stream Configuration, replace the default source name i

iiiTable of Contents1 Introduction 1Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26Setting Up the Kaleido-IP Multi-ViewerDefining Logical Sources2The Unicast Stream Configuration window appears.3. In Unicast Stream Configuration, r

Kaleido-IPQuick Start Guide272. In the Tools pane, expand the multi-viewer, and navigate to the transport stream for which you wish to define logical

28Setting Up the Kaleido-IP Multi-ViewerCreating a Room2Predefined destinations are mapped to monitor wall destinations by default.2. Adjust the numbe

Kaleido-IPQuick Start Guide295. Expand the filtered System list in the Tools pane, and then drag the appropriate output head onto the display.6. On th

30Setting Up the Kaleido-IP Multi-ViewerCreating a Layout2Creating a LayoutThe Kaleido-IP factory settings include three predefined layouts, which you

Kaleido-IPQuick Start Guide316. For every audio level meter in your layout, set the Audio format property to Auto.7. On the File menu, click Save. Alt

32Setting Up the Kaleido-IP Multi-ViewerConfiguring a Preset Button on the Kaleido-RCP22Configuring a Preset Button on the Kaleido-RCP2If your system

Kaleido-IPQuick Start Guide334. On the File menu, click Save. Alternatively, click the Save button on the toolbar.Step 5: Testing the Monitor Wall Ope

34Setting Up the Kaleido-IP Multi-ViewerUsing the Kaleido-RCP2 with Default Settings22. On the RCP2 unit, press the ENTER button and hold it until the

Kaleido-IPQuick Start Guide35Loading a LayoutTo load a layout on the monitor wall:1. Connect a mouse to the RCP2 (if available) and log on to the Kale

ivtoc

36Setting Up the Kaleido-IP Multi-ViewerLoading a Layout2

Contact Us!Miranda Technical SupportFor technical assistance, please contact the Miranda Technical Support center nearest you:Corporate Head OfficeMir

IntroductionWelcome to the Kaleido-X family of multi-viewers! This chapter provides information about system requirements, and items shipped with your

2IntroductionGetting Organized1video inputs over up to 12 displays, and capable of switching unprocessed inputs to 96 HD/SD router outputs.•The Kaleid

Kaleido-IPQuick Start Guide3• Keyboard, mouse for basic Kaleido-IP configuration• One dedicated 1000Base-T (or 100Base-T) Ethernet switch with enough

4IntroductionSystem Requirements for a Client PC1

Setting Up the Kaleido-IP Multi-ViewerThis chapter will guide you through the installation of a Kaleido-IP system in its default configuration.Summary