DENSITÉ series RCP-10x0 Remote Control Panel Guide to Installation and Operation M823-9900-100 17 Apr 2007
GUIDE TO INSTALLATION AND OPERATION 6 | RCP-10x0 Several network configuration options are available to IT personal to automate the process of findi
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 7 Functionality: • In CONFIG mode, the panel cannot be used to operate a router • In OPERATE mode
GUIDE TO INSTALLATION AND OPERATION 8 | RCP-10x0 Bus number (1-4) – enter the following data, depending on the mode selected in the pulldown • Sin
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 9 You must enter: • The IP address of the Densité frame in which the router is installed • The
GUIDE TO INSTALLATION AND OPERATION 10 | RCP-10x0 Click the Clear All button to empty all the checkboxes 3.4.6 Factory Values Click the Factory
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 11 The same comment applies if you have modified the IP address. The webpage will not automatically
GUIDE TO INSTALLATION AND OPERATION 12 | RCP-10x0 3.7 Button Labels All control panel buttons on the RCP-10x0 are unlabelled. • A space is lef
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 13 4 Operation The operations supported by the RCP-10x0 panel are straightforward in nature, but va
GUIDE TO INSTALLATION AND OPERATION 14 | RCP-10x0 4.1 Operating Modes The panel may be configured in any of the following operating modes: RCP-101
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 15 • The source buttons are assigned to 10 consecutive sources, beginning with a source that is spe
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 Safety Compliance Information Safety Compliance This equipment complies with: - CSA C22.2 No. 60950-
GUIDE TO INSTALLATION AND OPERATION 16 | RCP-10x0 4.5 Destination buttons (XY modes) In XY mode, the destination buttons are positioned as picture
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 17 1. PANEL ENABLE 2. DESTINATION (or BUS) LOCK 3. TAKE 4. DESTINATION (or BUS) PROTECT 4.6.
GUIDE TO INSTALLATION AND OPERATION 18 | RCP-10x0 4.6.2 TAKE Button The TAKE button has two applications: 1. PRESET – TAKE When the panel is in
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 19 4.6.3 LOCK button The LOCK button freezes the status of a router output bus: • Single bus mode
GUIDE TO INSTALLATION AND OPERATION 20 | RCP-10x0 • Both the LOCK button and the SOURCE button flash Crosspoints can only be inhibited at the route
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 21 RCP-1020 – Dual 10x1 RCP-1040 – Dual 20x1 RCP-1040 – Quad 10x1
GUIDE TO INSTALLATION AND OPERATION 22 | RCP-10x0 5 Troubleshooting Guide Here is what to do when you have a problem communicating between an HRS-
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 23 3. Set the DIP Switches on the panel to match the following image: ON2341 4. Push the reset b
GUIDE TO INSTALLATION AND OPERATION 24 | RCP-10x0 5.2 Panel configuration 1. From the computer, open a console (Start – Programs – Accessories – C
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 25 Densité Chassis to connect to using a hostname, you must specify a valid DNS server. If you are u
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 Table of Contents 1 RCP-10x0 Remote Control Panel ...
GUIDE TO INSTALLATION AND OPERATION 26 | RCP-10x0 5.3 Testing the connection to the HRS-1801… 5.3.1 …when using fixed IP parameters 1. Connect
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 27 2. Set the DIP Switches on the panel to match the following image: ON2341 3. If your Densité
GUIDE TO INSTALLATION AND OPERATION 28 | RCP-10x0 The slot number stating where the HRS-1801 sits in the frame in wrong The panel might be able to c
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 29 6 Specifications ETHERNET: 10/100 Base-T RJ-45 connector POWER SUPPLY Power over Etherne
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 5.2 Panel configuration...
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 1 1 RCP-10x0 Remote Control Panel 1.1 Introduction The RCP-10x0 is a series of panels providing f
GUIDE TO INSTALLATION AND OPERATION 2 | RCP-10x0 RCP-1040 In these diagrams, the upper and lower rows of elements are pushbuttons, while the cen
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 3 2 Installation 2.1 Unpacking The following items should be included in the RCP-10x0 package: •
GUIDE TO INSTALLATION AND OPERATION 4 | RCP-10x0 3 Configuration The RCP-10x0 remote control panel is configured with the use of an on-board web s
GUIDE TO INSTALLATION AND OPERATION RCP-10x0 | 5 Factory Default IP parameters IP address 192.168.100.100 Subnet mask 255.255.255.0 Gateway
Comments to this Manuals